> Serpent 733-TE 1/10 scale 4wd (#804001)
- Brand:
- Serpent
Product Type:- Gas Cars > 1/10 200mm
Serpent 733-TE Team Edition Serpent 200mm racecar with 4-wheel drive, 2-speed gearbox, independent suspension. 733-TE news: - SL6 new gearbox, with lower inertia, very reliable, new 2-speed gears - new rod type side stiffener - Direct Link System - SFC rear end; Serpent Flex Control rear end with connector-set - the rear anti-roll bar ball-bearings are seated in delrin bushings to isloate vibrations - the 2-speed shaft bearings are seated in delrin inserts for optimized fit and to isolate vibrations. - Mono-type engine mount - Mono-type ventilated brake-disk Developed, engineered and tested by Michael Salven, in close cooperation with Team Serpent drivers. Serpent, the racing experience
Related products
View: Text | Images
> Spare parts
| #1070 | Grommet rubber soft (4) High quality rubber grommets to be used for fueltank-mounting, servo supports and similar purposes. | View product >>> |
| #1377 | Thrust-bearing 5x10 High Quality thrust bearing for use with the Centax-II. | View product >>> |
| #1493 | Pressure nipple M3 (4) | View product >>> |
| #1494 | Silicone tubing 2x5mm 50 cm, transparent Special fuel resisitant silicone fuel line, size 2x5mm (internal diameter 1.5mm). Length 50cm. Color: transparent. | View product >>> |
| #160122 | Shock balljoint short on-road (2) Shock balljoint short on-road (2) | View product >>> |
| #1602 | Tank-clips small (10) Packet of 10 small body clips for mounting the fuel tank. Can also be used as body-clips for smaller rc cars. | View product >>> |
| #1639 | Collar alu 2.1+setscrew (4) Collars to use for the brake and throttlelinkages. | View product >>> |
| #1647 | Steel balls 6mm (4) | View product >>> |
| #1649 | Pivotball 5.8mm (20) Pack of 20 5.8mm Balls pivot balls with hex drive. | View product >>> |
| #1650 | Pivotball 5.8mm (4) Pivotball 5.8mm (4) | View product >>> |
| #1667 | Body-clip medium (10) Medium sized body-clips. 10 in a bag. In use for body-posts Serpent 710. | View product >>> |
| #401134 | Ball bearing 4x7 (2) Pair of 4x7 ball bearings. | View product >>> |
| #401458 | Diff gear 10T + diff axle for geardiff (2+1) Diff gear 10T + diff axle for geardiff (2+1) | View product >>> |
| #411063 | Pivot ball threaded upper arm (2) A pair of upper arm threaded Pivot balls. | View product >>> |
| #600117 | Tank cap seal silicone (2) Tank cap seal silicone (2) | View product >>> |
| #6503 | Cone flywheel 7mm long (3) Universal flywheel cone, set of 3. | View product >>> |
| #6582 | Centax clutchnut Replacement parts for Centax clutch system. | View product >>> |
| #6583 | Centax pre-load adjusting nut Replacement parts for Centax clutch system. | View product >>> |
| #6626 | Coilsprings and screws 2-speed Set of coilsprings and screws for 2-speed clutch shoes. Used for all Impact and Vector models. Lighter springs for Impulse gearbox available 801412. | View product >>> |
| #801215 | Wheelaxle front (2) Wheel-axle for Serpent Impulse, 705, 710, 720, 733. Hardened spring-steel, precision slots and threading. | View product >>> |
| #801217 | Wheelnut M4, flanged (4) use 110402 or 110452 | View product >>> |
| #801218 | Wheel hexagon alu 0mm (2) Alu. hex wheel adapters, anodized. Precision machined. Offset 0. | View product >>> |
| #801219 | Pivotball 8.5mm short (4) Set of four short aluminum 8.5mm pivot balls for use on the Serpent 705. | View product >>> |
| #802211 | Bodymount adjustable front (3) Full set of adjustable front body posts including the the third centre mount. Comes complete with mounting screws and body clips. | View product >>> |
| #802260 | Trackrod M3x47mm (2) Trackrod M3x47mm (2) | View product >>> |
| #802332 | Driveshaft (2) Set of 2 hardened steel driveshafts that are suitable for both the front and rear of the Serpent 710. | View product >>> |
| #802335 | Anti-Roll bar ball 3mm (2) A set of spare 3mm anti-roll bar balls. Comes supplied with grub screws. | View product >>> |
| #802352 | CVD Inserts (2) Pair of replacement inserts for the CVD shafts. | View product >>> |
| #802354 | Pin steel 3x9.8mm (4) Set of 4 spare steel pins size 2x9.8mm. Suitable for use in the optional Serpent 710 CVD system (#802350). | View product >>> |
| #802361 | Bodymount adjustable rear (2) Composite rear adjustable bodymount set complete with mounting screws and body clips. | View product >>> |
| #802403 | 2-speed spring (2) Pair of gearbox tension springs for use in the Serpent gearbox. | View product >>> |
| #802505 | Centax - 3 spring cup Aluminum spring cup for the Centax 3. | View product >>> |
| #802507 | Centax - 3 centrifugal shoes (3) Set of 3 centrifugal shoes for the Centax 3. | View product >>> |
| #803134 | Spacer anti roll bar RR (2) Spacer (2) for the rear anti roll bar. Comes complete with grub screws. | View product >>> |
| #803135 | Anti-roll bar RR 2.5mm Rear anti-roll bar (2.5mm) for use with the Serpent 720 and 733. | View product >>> |
| #803198 | Adjusting nut nylon for 8.5mm ball (10) Set of 10 nylon end play adjusting nuts for use with the cars 8.5mm pivot balls. | View product >>> |
| #803208 | Centax-3 flywheel 31mm 31mm diameter Centax-3 flywheel. | View product >>> |
| #803230 | Centax-III clutch set WC (no flywheel) Centax-III WC clutch set for use on a 1/10th scale Serpent chassis. Comes complete with bell housing, clutch shoe, 2 new WC pinions, clutch plate, flyweights, spring, bearings, spacers and everything needed to mount it in your car, except the flywheel. To be used only with WC 2 speed gears. | View product >>> |
| #803231 | Centax-3 WC Clutch bell housing Centax-3 WC Steel Clutch bell housing. | View product >>> |
| #803232 | Centax-3 WC Gear set alu (6) Set of 6 hard coated aluminium pinion gears for the Centax-3 WC clutch system. Set includes 1st gears - 16T, 17T & 18T and 2nd gears - 21T, 22T & 23T. | View product >>> |
| #803233 | Pinion Centax-3 WC (1st) 16T Hard coated aluminium 16T 1st gear pinion for the Centax-3 WC clutch system. | View product >>> |
| #803234 | Pinion Centax-3 WC (1st) 17T Hard coated aluminium 17T 1st gear pinion for the Centax-3 WC clutch system. | View product >>> |
| #803236 | Pinion Centax-3 WC (2nd) 21T Hard coated aluminium 21T 2nd gear pinion for the Centax-3 WC clutch system. | View product >>> |
| #803237 | Pinion Centax-3 WC (2nd) 22T Hard coated aluminium 22T 2nd gear pinion for the Centax-3 WC clutch system. | View product >>> |
| #803240 | CV-axles set pro Set of 2 high performance CVD shaft assemblies in durable Serpent spring-steel quality for use on Serpents range of 1/10th 200mm. | View product >>> |
| #803241 | CVD Drive shaft (2) A pair of spare high quality spring steel CVD drive shafts for the Serpent 710, 720, 733. | View product >>> |
| #804100 | Belt Front 40S3M195 Kevlar re-inforced drive-belt 4mm wide, 195T. | View product >>> |
| #804101 | Belt Side 40S3M378 Kevlar re-inforced drive-belt 4mm wide, 378T. | View product >>> |
| #804103 | Belt Set 733 (3) Kevlar re-inforced drive-belt-set 5mm wide rear 186T belt, 4mm wide front 195T and 378T side belt. | View product >>> |
| #804108 | Up-right 733 (2) Rear up-right in nylon for 733. Uses same left and right. | View product >>> |
| #804109 | Wishbone rear lw L+R Medium wishbone rear lower MEDIUM, L+R the same. | View product >>> |
| #804110 | wishbone front lw L+R Medium wishbone front lower MEDIUM, L+R . | View product >>> |
| #804111 | Wishbone front up L+R Medium (2) wishbone front upper MEDIUM, L+R (same). | View product >>> |
| #804112 | Pully 2speed shaft 20+21T (2) Reinforced nylon pullies, perfectly true running, low wear. Feature small holes in the sides to allow dirt/dust out. | View product >>> |
| #804113 | Pully middle 18+21T (2) Reinforced nylon pullies, perfectly true running, low wear. Feature small holes in the sides to allow dirt/dust out. | View product >>> |
| #804114 | 2-speed shaft 733 Balanced 2-speed gearbox shaft. Serpent spring steel. Calibrated holes for steel pins, chamfered flat spot. | View product >>> |
| #804115 | Exhaust mount spring Spring steel exhaust mount spring, to fix the pipe-set safely to the radioplate. The spring will prevent the pipe to damage (at small impact only). | View product >>> |
| #804116 | Pivot pin rr lw (2) Spring steel rear lower pivot pins, with chamfered flat spots. Packed by 2. | View product >>> |
| #804117 | Pivot pin fr lw (2) Spring steel front lower pivot pins, with chamfered flat spots. Packed by 2. | View product >>> |
| #804118 | Pivot pin fr up (2) Spring steel front upper pivot pins. Packed by 2. | View product >>> |
| #804119 | Bumper 733 foam (2) Foam bumper standard version. High quality foam, absorbs impact in perfect way. Packed by 2. | View product >>> |
| #804120 | Servo saver axle Servo saver axle. Precision machined axle for perfect bearing fit. Serpent spring steel. | View product >>> |
| #804121 | Shaft middle Shaft middle steel. Precision machined with calibrated holes for the steel pins and axle for perfect bearing fit. Serpent spring steel. | View product >>> |
| #804122 | Bearingblock rr up alu Bearingblock rear upper alu. Precision machined alu bearingblock, anodised in titanium color. | View product >>> |
| #804123 | Belt tensioner alu Belt tensioner in aluminium. Precision machined, anodised in titanium color. | View product >>> |
| #804124 | Servo saver spring Servo saver spring. | View product >>> |
| #804128 | Rearplate wide alu Rear suspension bracket wide version. Precision machined aluminium, engraved and anodised. | View product >>> |
| #804130 | Servo saver nut alu Servo saver nut alu, to set the preload on the servo-saver spring. | View product >>> |
| #804131 | Servo saver shaft alu Servo saver shaft alu, with alu threading. | View product >>> |
| #804132 | Suspension bracket rr fr alu V0 Suspension bracket in CNC machined high grade alu. Anodised. Rear side, front one V0, which is the wide version. | View product >>> |
| #804134 | Bracket middle shaft alu CNC machined alu middle shaft bracket, anodised. | View product >>> |
| #804135 | Chassisplate 733 3mm CNC machined 3mm aerospace quality 7075 T6 aluminium. Closed design, to create stiff chassis. Chamfered edges, countersunk holes, recess for transponder mounting, cooling holes for the engine. | View product >>> |
| #804136 | Battery holder carbon CNC machined high quality carbon fibre, lightweight bracket to attach the battery. | View product >>> |
| #804137 | Radioplate 733 carbon CNC machined high quality carbon fibre, lightweight radioplate 2.5mm | View product >>> |
| #804138 | Shocktower front 733 carbon CNC machined lighweight, high quality carbon fibre 3.2mm, front shocktower. Selection of shockmounting positions and place to mount 3rd body post. | View product >>> |
| #804139 | Shocktower rear 733 carbon CNC machined lighweight, high quality carbon fibre 4mm, rear shocktower. Selection of shockmounting positions and place to push through the tank-opening-wire. | View product >>> |
| #804140 | Camber link bracket 733 carbon CNC machined lighweight, high quality carbon fibre, rear camber link bracket. Selection of mounting positions also inner and outer. | View product >>> |
| #804143 | Anti-rollbar FR 2.5mm Precision made spring-steel front anti-roll bar in 2.5mm | View product >>> |
| #804145 | Exhaust spring holder alu CNC machined alu exhaust spring holder. | View product >>> |
| #804146 | Shim conical 3x2mm (4) Shim conical 3x2mm (4), to used as roll-center spacer, on top of the up-right. Orange anodised. Works in 1/8 and 1/10 scale. | View product >>> |
| #804147 | Diff pulley front 35T Diff pulley front 35T, for gear-diff and or spool/oneway shaft. | View product >>> |
| #804148 | Diff pulley rear 40T Diff pulley rear 40T, for gear-diff. | View product >>> |
| #804149 | Tank inserts (frame) Nylon , injection moulded inserts, that can be mounted inside the fueltanks with a screw, to reduce volume if needed, due to higher temperature or other. 3 sizes on one frame. | View product >>> |
| #804150 | Rollbar 733 Nylon rollbar 733, which doubles as end-stop for the fuel-tank cap and also incorporates a guider for the tank-cap-opening wire. | View product >>> |
| #804151 | Receiver box Nylon receiver box, to mount and protect your precious receiver. Sports S-logo on the side. | View product >>> |
| #804152 | Eccenters rear frame Frame which includes the eccenters of the rear suspension. To change the pivot pin positons. | View product >>> |
| #804153 | Eccenters front frame Frame which includes the eccenters of the front suspension. To change the pivot pin positons. | View product >>> |
| #804154 | Servo levers steering (3) Frame with the 3 most commonly used levers for steering, 23T, 24T and 25T. Precison fit. | View product >>> |
| #804155 | Servo levers throttle (3) Frame with the 3 most commonly used levers for throttle, 23T, 24T and 25T. Precison fit. | View product >>> |
| #804156 | Brake-lever/battery spacers frame Frame with the nylon brake lever, and the spacers to correctly mount the battery bracket. | View product >>> |
| #804157 | Servo-saver set nylon Nylon frame contains the parts of the servo-saver. | View product >>> |
| #804158 | Servo-mounting spacers Nylon spacer to correctly mount the servo. | View product >>> |
| #804159 | Steering-servo mount Steering-servo mount in nylon. | View product >>> |
| #804160 | Bearing bracket upper front Front upper top-mounted bracket in nylon. | View product >>> |
| #804161 | Suspension bracket front L+R Suspension bracket front L+R . | View product >>> |
| #804162 | Radioplate support (2) Radioplate support in nylon, 2 pcs. | View product >>> |
| #804163 | Chassis stiffner, side Nylon chassis stiffner, connects rear end to the radioplate. | View product >>> |
| #804164 | Bodyplate front Nylon bodyplate front. | View product >>> |
| #804165 | Bumperplate front Bumperplate front nylon. | View product >>> |
| #804166 | Bearingblock FR L alu CNC machined, anodised, aluminium, front left bearingblock. | View product >>> |
| #804167 | Bearingblock FR R alu CNC machined, anodised, aluminium, front right bearingblock. | View product >>> |
| #804168 | Bearingblock RR alu CNC machined, anodised, aluminium, rear bearingblock. | View product >>> |
| #804169 | Brake pulley adaptor alu Machined alu brake pulley adaptor with 3 steel pins. | View product >>> |
| #804170 | Suspension bracket front alu CNC machined alu front suspension bracket, anodised. | View product >>> |
| #804171 | Geardiff uni 733 Complete set to assemble the universal 733 geardiff. Fits front and/or rear. Supersmall, very light, strong case. 22 gram incl main gear. | View product >>> |
| #804173 | Gear-diff revision-set Gear-diff revision-set. | View product >>> |
| #804174 | Gear-diff housing Precision moulded nylon gear-diff case. | View product >>> |
| #804175 | Suspension-set nylon Medium (10) Suspension-set nylon MEDIUM, includes 10 pcs of the main suspension parts for a rebuild. | View product >>> |
| #804176 | Geardiff X-ring (4) X-shaped gear-diff seal in top quality silicone rubber. 4 pieces. | View product >>> |
| #804178 | Tank-support alu / rubber (3) 3 pieces of alu tank supports and silicone rubber covers. | View product >>> |
| #804179 | Tank-mounts rubber (3) Tank-mounts rubber (3) | View product >>> |
| #804180 | Brake / throttle wire (2) Threaded wire with end-stop to use for throttle and brake linkages. | View product >>> |
| #804181 | Throttle spring (2) Small throttle spring (2) | View product >>> |
| #804182 | Decal sheet 733 (2) High quality, thin foil-type decal-sheets with 733 logo's, to apply to bodyshells. | View product >>> |
| #804183 | Manual - ref guide 733 full color Full color manual and reference guide for 733. | View product >>> |
| #804186 | Screw-set 733 (196) Complete set of screws for 733, top quality allen type steel screws. | View product >>> |
| #804187 | Oil-set 733 (3) Silicone oil-set of 733 kit. Includes shockoil 1000 Cst and 2 types diff oil, 80k and 50k. | View product >>> |
| #804188 | Driveshaft adaptors geardiff Pro (2) Spring steel, lightened drive shaft adaptors for gear-diff 733. 2 pieces. | View product >>> |
| #804200 | Diffcase O-ring EP (10) Diffcase O-ring 22,5x1 (10) | View product >>> |
| #804202 | Belt rear 50S3M186 Kevlar re-inforced drive-belt 5mm wide, 186T. | View product >>> |
| #804217 | Bearingblock-2sp-r 733 / 966 V2 Bearingblock-2sp-r 733 / 966 V2 With this bearingblock you can connect them to the rear bearingblocks to make the car stiffer. | View product >>> |
| #804218 | Bearingblock-2sp-l 733 / 966 V2 Bearingblock-2sp-l 733 / 966 V2 With this bearingblock you can connect them to the rear bearingblocks to make the car stiffer. | View product >>> |
| #804219 | Bearingblock rear upper 733 V2 Bearingblock rear upper 733 V2. With these bearingblocks you can connect them to the 2-speed bearingblocks to make the rear end stiff. | View product >>> |
| #804220 | Bushings bearingblock l+r 733 / 966 V2 (2) Bushings bearingblock l+r 733 / 966 V2 (2) | View product >>> |
| #804221 | Bushing rear anti-roll bar L+R 733/966 V2 (2) Bushing rear anti-roll bar L+R 733/966 V2 (2) | View product >>> |
| #804222 | Rear end V2 upgrade set 733 Rear end V2 upgrade set 733 New rear end parts enable connecting rear end and 2-speed brackets with rubber or aluminium connectors, for more or less flex. Delrin bushings are included to seat the anti-roll bar bearings and 2-speed axle bearings. | View product >>> |
| #804223 | Direct Link-Set DLS The Direct Link system is activated during cornering mainly, whereby the outer suspension forces are transfered partially to the inner wheel too, with a pivot-link system. The set includes the carbon fibre camber bracket, 2 carbon fibre brackets for the lower arms, strong springs steel push rods, cnc machined alu pivots with precison fit ball-bearings, aluminum bearing shafts and spacers, a frame op top quality ball-joints ( with some spares ones ) and hardware as needed. A full instruction sheet is provided too. | View product >>> |
| #804224 | Camber bracket carbon DLS Camber bracket carbon DLS | View product >>> |
| #804225 | Support brackets carbon DLS (2) Support brackets carbon DLS (2) | View product >>> |
| #804226 | Pivot lever alu (2) Pivot lever alu (2) | View product >>> |
| #804227 | Enginemount mono 733 Enginemount mono 733 (one piece enginemount). Beautifully designed and machined mono-engine block for Serpent 733 in top quality aluminum. Grey anodized finish.Very strong and durable, creates a stiffer chassis in that area, so reduction of flex. Fits all main brands of engines. Direct replacement of multi-part kit-version | View product >>> |
| #804228 | Connectorset rear 733 (2+2) Connectorset rear 733 (2+2) Set of 2 rubber and 2 alu connectors with screws as needed. Use together with 804222 | View product >>> |
| #804231 | Dls shaft (2) Dls shaft (2) | View product >>> |
| #804232 | Shim 3x6x3 (4) Shim 3x6x3 (4) Repalced by 110417 Shim 3X6X3 (10) | View product >>> |
| #804235 | Gearbox SL6 for 733 Complete new gearbox for Serpent 733. Its standard on the 733-Team Edition and fits earlier models of 733 cars. The all new design gearbox has very low inertia, lighter adaptor, lighter aluminum bell and one-way adaptor with German oneway, new steel shaft, smaller shoes and new beautifully designed gears. Includes rod type side stiffner with balljoints. | View product >>> |
| #804236 | 2-speed adaptor SL6 2-speed adaptor for the SL6 gearbox | View product >>> |
| #804237 | 2-speed shoe SL6 (2) 2-speed shoe for the SL6 gearbox (2) | View product >>> |
| #804238 | 2-speed drive flange SL6 Replaced by 804378 | View product >>> |
| #804239 | 2-speed housing SL6 2-speed housing for the SL6 gearbox | View product >>> |
| #804240 | 2-speed shaft SL6 2-speed shaft for the SL6 gearbox | View product >>> |
| #804241 | 2-speed gear set SL6 (6) 2-speed gear set SL6 (6) | View product >>> |
| #804243 | 2-Speed gear 59T SL6 2-Speed gear 59T SL6 | View product >>> |
| #804244 | 2-Speed gear 60T SL6 2-Speed gear 60T SL6 | View product >>> |
| #804247 | 2-Speed gear 55T SL6 2-Speed gear 55T SL6 | View product >>> |
| #804248 | Fueltank 75cc Fueltank 75cc with new shorter cap and new seal. Fitted with brass sintered filter. Made from heat resistant material. Enables fitting spacers inside to reduce volume as required. | View product >>> |
| #808214 | Spacer-set caster (3) Set of 2 nylon frames with 1-2-4mm caster shims. The shims can be placed in front or behind the upper suspension arm, therewith changing the caster angle of the front suspension. | View product >>> |
| #901255 | Belt tensioner Alu. belt tensioner S950, S835, S705, VETEQ. | View product >>> |
| #902138 | Trackrod M3x23 (2) Trackrod M3x23 (2) | View product >>> |
| #902420 | Roller pin steel 5X5 (2) A pair of steel roller pins for use in the LC gearbox. Replaced by 110202 Pin 5x5 (10) | View product >>> |
| #902421 | Needle 3x13.8 (4) Set of 4 Roll pins for use with the new LC Gearbox 2 speed adapter. Replaced by 110203 Pin 3x14 (10) | View product >>> |
| #903166 | Shock rod short (2) A set of 2 short shock rods for use in RCC shocks. | View product >>> |
| #903168 | Nylon parts frame shocks RCC Complete set (4) of composite RCC shock absorber components. | View product >>> |
| #903171 | O-ring 10x1 (4) Set of 4 o-rings for use in the RCC shock absorbers. | View product >>> |
| #903175 | Foam insert (4) Set of 4 foam inserts for use in the RCC shock absorbers. | View product >>> |
| #903177 | Nut shock alu (2) Set of 2 anodised aluminium shock absorber nuts. Suitable for the RCC shock absorbers. | View product >>> |
| #903178 | Body alu shock FR (2) A pair of front aluminium RCC shock bodies. | View product >>> |
| #903186 | C + G Clip + washer RCC shocks (12) Set of 4 C-clips (R2), G-clips and nylon washers, suitable for Serpents RCC shocks. | View product >>> |
| #903231 | Ball joints set 14+6+2 Set of composite ball joints that includes 14 x 6mm ball joints, 6 x shorter shock end ball joints and 2 x 4mm ball joints. The balljoints feature a text with TOP to indicate right position to press in the ball, for perfect fit. | View product >>> |
| #903318 | Brake cam alu 966 Hard-coated aluminium brake-came. | View product >>> |
| #903319 | Brake bushing (2) Brake bushing in spring steel, 2 pieces. | View product >>> |
| #903330 | Brakeplate and pad set Brakeplate and pad set | View product >>> |
| #903333 | X-ring RCC 2009 Shock (10) X-Ring for the 2009 RCC Shock | View product >>> |
| #903334 | Shock-set RCC-X short (2) Complete pre assembled short RCC-X shock absorbers. Comes with optional 1, 2 & 4 hole pistons. The 2009 version RCC-X has a better seal / support package. The shockrod is supported better with the delrin bushing, and a new design x-ring, made of a special silicone rubber (instead of an o-ring) provides a better seal at less friction. A new mould for the nylon parts has been made, so also the nylon parts of the shocks are improved, both pistons and ball-joints too. Supersmooth shocks ! Fits all 1/8 and 1/10 gas-cars, but also 1/10 electric touringcars. | View product >>> |
| #903336 | 903336 Insert RCC 2009 shock (2) Shock bottom for the X-Ring for the 2009 RCC shock | View product >>> |
| #903341 | Antirollbar ball 3mm (2) Antirollbar ball 3mm (2) | View product >>> |
| #903347 | Balljoint shock RCC (4) Precision moulded lower short ball-joints of the RCC shocks. Packed by 4. | View product >>> |
| #909405 | Shock adjusting nut alu. + O-rings (4) Set of 4 alu. spring-tension adjusting nuts and 4 O-rings to be inserted into the alu. adjusting nuts. O-ring prevents adjusting nut from coming loose. | View product >>> |
| #909516 | Centax II Spacer Thrustbearing Sapcer for use with Centax-II clutch system. Comes complete with screw. | View product >>> |
| #909519 | Centax II shims 5 x 10 x 0.3 (2) + 0.5 (1) Set of 3 Centax-II shims in two sizes 0.3 (2) and 0.5 (1). | View product >>> |
| #909520 | Centax II / III spring 1.8 (10mm) Optional 10mm Centax II spring. | View product >>> |
| #9638 | Spacer aluminium for 2-speed shaft To use on 2-speed shaft on Impulse, Impact 2WD. | View product >>> |
News