The Serpent 835 follows in the prestigious footsteps of the World and National Champion Serpent Impact M2 Challenger. Incorporating many of the new features the Serpent Race Team developed, the 835 will continue to be the choice of champions in the 1/10 scale 235mm class for years to come.
#1065 | O-rings alu front axle (10) | View product >>> |
#1070 | Grommet rubber soft (4) High quality rubber grommets to be used for fueltank-mounting, servo supports and similar purposes. | View product >>> |
#1093 | Centax 5x8 shim-set 0.1 (2) 0.3 (1) Special shims to adjust end-play on the Centax clutch housing. Shims are used on the outside of the thrust-bearing bushing. Set includes 2 shims of 0.1mm and 1 shim of 0.3mm. | View product >>> |
#1601 | Body clips (10) Set of 10 galvanised steel body-clips. | View product >>> |
#1602 | Tank-clips small (10) Packet of 10 small body clips for mounting the fuel tank. Can also be used as body-clips for smaller rc cars. | View product >>> |
#1615 | Ball-joints 4mm (4) | View product >>> |
#1619 | Wire-guider nylon Nylon parts through which the throttle or brake-linkage slides. | View product >>> |
#1636 | Universal throttle linkage set | View product >>> |
#1637 | Universal adjustable brake-set | View product >>> |
#1639 | Collar alu 2.1+setscrew (4) Collars to use for the brake and throttlelinkages. | View product >>> |
#1647 | Steel balls 6mm (4) | View product >>> |
#1649 | Pivotball 5.8mm (20) Pack of 20 5.8mm Balls pivot balls with hex drive. | View product >>> |
#1650 | Pivotball 5.8mm (4) Pivotball 5.8mm (4) | View product >>> |
#1660 | Ball-joint set 6mm (20 pieces) Set of 20 ball joints in 6.0mm diameter. Replacement set for VETEQ pushrod ball-ends. Made of high-tensile composite material for increased wear resistance. | View product >>> |
#6361 | Drive belt short (Kevlar) 201X6MM Timing belt for rear transmission of Impact and Impulse, and used on front transmission of Vector, S950, S950R. replacement belts: www.serpent.com/903296 www.serpent.com/903300 | View product >>> |
#6503 | Cone flywheel 7mm long (3) Universal flywheel cone, set of 3. | View product >>> |
#6581 | Centax flywheel 35mm Centax flywheel. Diameter 35mm. Hard anodized and PTFE coated. For use with Centax and Centax II with the Serpent 705 and 835. | View product >>> |
#6582 | Centax clutchnut Replacement parts for Centax clutch system. | View product >>> |
#6583 | Centax pre-load adjusting nut Replacement parts for Centax clutch system. | View product >>> |
#6584 | Centax spring cup Replacement parts for Centax clutch system. | View product >>> |
#6589 | Centax spacer thrust bearing Replacement parts for Centax clutch system. Replacement partnr: 909516 | View product >>> |
#6599 | Centax shim-set Shim set to adjust position of Centax flywheel on crankshaft. Set of 10 shims 4pcs 7x13x0.1, 2pcs 7x13x0.3mm, 4pcs 7x13x0.5mm. | View product >>> |
#801156 | Bracket tank-mounting nylon Composite bracket for mounting rear of fuel tank to radio plate. Comes with rubber grommit. | View product >>> |
#801158 | Spacer tank-mounting 3.1 x 8 x 3 mm (2) Tank mounting post base. Packet of 2. | View product >>> |
#801171 | Battery-case + connector Composite battery case and front mount for use with the Serpent 705 and 835. | View product >>> |
#801172 | Battery-case connector Composite set of battery mounts for use with the Serpent 705 and 835. | View product >>> |
#801212 | Steeringblock left FC Optional composite left steering block. FC for fluent cornering. Use smaller bearings 10x15x4 (lighter) and new shorter PTFE coated aluminium pivot balls. | View product >>> |
#801213 | Steeringblock right FC Optional composite right steering block. FC for fluent cornering. Use smaller bearings 10x15x4 (lighter) and new shorter PTFE coated aluminium pivot balls. | View product >>> |
#801331 | Bearing Block rear left Left rear composite bearing block for use on the Serpent 705 and 835. | View product >>> |
#801332 | Bearing block rear right Right rear composite bearing block for use on the Serpent 705 and 835. | View product >>> |
#801342 | Diskbrake bracket Composite upper rear brake bracket with top mounted anti-roll bar position for use with Serpent 705 and 835. | View product >>> |
#801415 | 2-speed axle 4WD 705-835 Two speed axle for Serpent 705 and 835 for use with LC gearbox. Comes with c-clips and drive pin. | View product >>> |
#801430 | Ball. Differential Adj (excl. Pulley) Complete adjustable Ball differential for use with the Serpent 705 and Impulse. Comes with everything needed to complete except for the pulley. The color of the diff-shafts will change to black. | View product >>> |
#801431 | Diff. axle short + adj screw M5 Short steel diff axle for use with Serpent 705. Comes with steel adjusting screw. | View product >>> |
#801432 | Diff. axle long Long steel diff axle for use with Serpent 705. Color-coating will change to black. | View product >>> |
#801433 | Adjusting diff. Screw steel M5 Steel adjusting nut for Serpent adjustable differential. | View product >>> |
#808103 | Chassisplate alu. 4mm T6 3mm aerospace quality CNC machined aluminum chassis plate for Serpent 835. Countersunk holes, extra cooling slots below the engine, chamfered edges. | View product >>> |
#808110 | Radio plate carbon 2mm CNC Machined 2mm carbon fibre radio plate for the Serpent 835. | View product >>> |
#808111 | Spacer sideplate Left (3) Set of three spacers for Serpent 835 to be used with mounting the left sideplate. | View product >>> |
#808120 | Bumper Impact-2 / M2 Universal front bumper, fits all versions Impact 2 and M2. | View product >>> |
#808125 | Shocktower carbon front M2 Optional universal front shock tower for Impact M2 and 2, fits all Specs. Set comes with 4 hardened pivot balls and hardware. Machined of woven graphite composite material. Shock tower enables 2 shock positions for better tunability of front suspension. | View product >>> |
#808130 | Bodyplate front | View product >>> |
#808138 | Shock-support rear carbon/ball-set This shock bracket in carbon fibre can be used on 235mm Serpent cars and S705 and Impulse cars. For some tracks this may work better than the shocktowers. Upper central hole to put a tie-wrap through for quick tank-refills. | View product >>> |
#808140 | Bodymount-set rear TC Bodymount for Impact 2 and M2, to fit Touring car type bodies. | View product >>> |
#808141 | Body-support long front (2) | View product >>> |
#808142 | Body-support short front (2) | View product >>> |
#808143 | Bodysupport-set carbon rear Body-support set rear for Impact M2 and Impulse kits, all versions, when using the touring-car bodies mainly. The set includes the universal bodymounts, the carbon mounting strip and 2 conical alu washers . | View product >>> |
#808150 | Bodymount-set rear GTP EV2 Rear bodymount set for Impact M2 Spec 2000, to fit GTP type bodies. | View product >>> |
#808151 | Pins lower for bodysupport (2) | View product >>> |
#808152 | Centering bushing threaded | View product >>> |
#808185 | Manual Serpent 835 Full colour instruction manual for Serpent 835. Includes Set-up guidelines at the rear of the manual. | View product >>> |
#808186 | Reference guide Serpent 835 Full colour Reference guide for Serpent 835. Includes full parts list at the rear of the guide. | View product >>> |
#808201 | Front bearing block left Front bearing block left for Impact 2 and M2 all versions, and Impulse. | View product >>> |
#808202 | Front bearing block right Front bearing block right for Impact 2 and M2 all versions, and Impulse. | View product >>> |
#808203 | Wishbone front top left Front wishbone top left for Impact 2 and M2 all versions, and Impulse. | View product >>> |
#808204 | Wishbone front top right Front wishbone top rightt for Impact 2 and M2 all versions, and Impulse. | View product >>> |
#808205 | Wishbone front bottom left Front wishbone bottom left for Impact 2 and M2 all versions, and Impulse. | View product >>> |
#808206 | Wishbone front bottom right Front wishbone bottom right for Impact 2 and M2 all versions, and Impulse. | View product >>> |
#808207 | Steering block left Steering block left for Impact 2 and M2 all versions. | View product >>> |
#808208 | Steering block right Steering block right for Impact 2 and M2 all versions. | View product >>> |
#808210 | Hinge pins front top (2) High-tensile steel hinge pins for upper front suspension arms. Length = 54mm. Fit all Impact 2 and M2 versions. | View product >>> |
#808212 | Hinge pins front bottom (2) High-tensile steel hinge pins for lower rear suspension arms. Length = 88mm. Fit all Impact 2 and M2 all specs, and Vector all specs.. | View product >>> |
#808214 | Spacer-set caster (3) Set of 2 nylon frames with 1-2-4mm caster shims. The shims can be placed in front or behind the upper suspension arm, therewith changing the caster angle of the front suspension. | View product >>> |
#808215 | Front wheel axles set 4-WD (2) Standard front wheel axles for 4-WD Impact 2 and M2 all Specs. Made of high tensile steel and heat treated for extreme durability. Designed as quick-change system. Otional fixed wheel adpaters 808330 available. Set includes q-c springs, shims and pins. | View product >>> |
#808219 | Front axle alu. with PRO one-way bearings Special version of the front axle features one-way bearings with extra sintered bronze support bushings. Replaces standard front axle 808221. For Impact 2 and M2 and Serpent 835 4-WD all Specs. | View product >>> |
#808220 | Front drive-shafts (2) Ultra durable, light yet strong precision machined front drive shafts for Impact 2 and M2 4-WD all Specs. Replacement pins available (808328). | View product >>> |
#808221 | Front axle alu. with one-way bearings Alu. front axle for 4-WD Impact 2 and M2 all Specs, with 1-way bearings pressed in. Use only Serpent One-Way Lube 1680 to lubricate the one-way bearings. | View product >>> |
#808225 | Pulley / washer 16T Pulley 16T for middle shaft (center). For 1/10 scale. | View product >>> |
#808226 | Pulley / washer 19t Pulley 19T for middle shaft (side). Impact 2. | View product >>> |
#808227 | Pulley / washer 22t Pulley 22T for middle shaft (side). For Impact 2. | View product >>> |
#808228 | Pulley / washer 23t Optional pulley 23T for middle shaft (side). For Impact 2 and M2 all Specs. Generates more drive to the front wheels. | View product >>> |
#808229 | Pulley / washer 24t Pulley 24T for front shaft. For Impact M2 all Specs and Impulse solid front axle 801240. | View product >>> |
#808232 | Q-c springs (4) Set of 4 springs for the quick-change release wheel axles. Suitable for front and rear wheel axles on Impact 2 and M2 all Specs. | View product >>> |
#808245 | Front anti-roll bar adjustable Optional adjustable front anti-roll bar for Impact 2 and M2 all Specs and Impulse. Interchangeable with standard front anti-roll bar 808239. | View product >>> |
#808250 | Middle bearing block 4-WD Middle bearing block for 4-WD Impact 2 and M2 all Specs, and Vector all Specs. | View product >>> |
#808252 | Middle shaft High tensile steel middle shaft for 4-WD Impact 2 and M2 all Specs, and Vector all Specs. | View product >>> |
#808260 | Pulley 18t Pulley 18T for 2-speed shaft (side) Impact M2 all versions. Not interchangeable with Impact 2. | View product >>> |
#808261 | Pulley / flange 24T Pulley 24T for middle shaft (side) 1/10 scale. | View product >>> |
#808265 | Pulley adaptor alu. Alu. pulley-adapter for Impact 2 and M2 all versions, used on middle shaft pulleys. | View product >>> |
#808311 | Up-right low (1) Up-right Spec 2000. Lowered version (3mm) for improved handling characteristics. Increased track-width of rear suspension with 4mm. Can be used on Spec 98 and 99 versions. Left and right unit are identical. | View product >>> |
#808312 | Pivot ball 9mm hardened (2) Hardened pivot balls used in upper rear suspension arms. Fit Impulse, Impact 2 and M2 all Specs, and Vector all Specs.. | View product >>> |
#808313 | Spacer 7mm alu for rear upright +screw (2) 7mm Aluminium spacer for use with the Impulse. Creates a different rear wishbone geometry. | View product >>> |
#808315 | Pivot pins rear top (2) High-tensile steel hinge pins for upper rear suspension arms. Length = 43mm. Fit all Impact 2 and M2 versions. | View product >>> |
#808317 | Pivot pins rear bottom (2) High-tensile steel hinge pins for lower rear suspension arms. Length = 63mm. Fit all Impact 2 and M2 versions. | View product >>> |
#808320 | Rear wheelaxles-set (2) Rear wheel axles for Impact 2 and M2 all Specs. Made of super durable high tensile and heat treated steel. Designed as quick-change system. Otional fixed wheel adpaters 808330 available. Set includes q-c springs, shims and pins. | View product >>> |
#808323 | Q-c levers rear alu (2) Alu. quick-change levers for the rear wheel axles. Interchangeable with standard parts 808322. | View product >>> |
#808325 | Drive-shafts rear (2) Ultra durable, light yet strong precision machined rear drive shafts for Impact 2 and M2 all Specs. Replacement pins available (808327 or 808328). | View product >>> |
#808337 | Anti-roll bar set rear 1.5mm Optional non-adjustable rear anti-roll bar for Impact 2 and Impact M2 all Specs. Size 1.5mm (softer). | View product >>> |
#808338 | Linkages rear anti-roll bar | View product >>> |
#808340 | Ball-cups set nylon (12) Universal ball cups made of special low-friction composite material. Used on all models of Impulse, Impact 2 / M2 and Vector. | View product >>> |
#808342 | Wheelaxle pins / shims (4) | View product >>> |
#808344 | Alu.adjusting nuts M10 (4) Universal alu. adjusting plugs with M10. Used on all models Impulse, Impact and Vector on steering blocks and up-rights. | View product >>> |
#808346 | Pivot-balls 8.5mm (2) Universal pivot balls. Used in all Impulse, Impact 2 / M2 and Vector models on front and rear suspension. | View product >>> |
#808349 | Brake cam alu hard anodised M2 Optional alu. brake cam, hard anodized for extra durability. Better suited for driving in wet conditions. Interchangeable with standard brake cam 808354. | View product >>> |
#808350 | Rear bearing block left M2 99 Rear bearing block (left) for Impact M2 Spec 99 and 2000. Cannot be used on Spec 98 unless also wishbones are replaced. | View product >>> |
#808351 | Rear bearing block right M2 99 Rear bearing block (right) for Impact M2 Spec 99 and 2000. Cannot be used on Spec 98 unless also wishbones are replaced. | View product >>> |
#808353 | Brake bracket nylon Spec 2000 Brake bracket for Impact M2 Spec 2000. Suitable to be used with optional chassis stiffener 808365. | View product >>> |
#808355 | Rear plate M2 Rear plate for Impact M2 all Specs. Not interchangeable with Impact 2. Uses different rear anti-roll bar mounting. | View product >>> |
#808356 | Wishbone rear top left M2 Wishbone rear top left for Impact M2 all Specs. | View product >>> |
#808357 | Wishbone rear top right M2 Wishbone rear top right for Impact M2 all Specs. | View product >>> |
#808358 | Wishbone rear bottom left M2 99 Wishbone rear bottom left for Impact M2 all Specs. | View product >>> |
#808359 | Wishbone rear bottom right M2 99 Wishbone rear bottom right for Impact M2 all Specs. | View product >>> |
#808360 | Drive-belt front 4mm Kevlar reinforced timing belt for Impulse, Impact 2 and M2 all Specs, width 4mm. Front belt used between middle shaft and front shaft. | View product >>> |
#808362 | Drive-belt side 4mm Kevlar reinforced timing belt for Impact 2 and M2 all Specs, width 4mm. Side belt used between lay shaft and middle shaft. | View product >>> |
#808370 | Solid rear axle set Solid rear axle set for Impact M2 all Specs (rear transmission ratio 47T/22T). Set includes pulley 47T and pin. Not interchangeable with Impact 2 versions. | View product >>> |
#808371 | Solid axle pulley 46T Pulley for use with solid rear axle. Impact 2 version only (Impact 2 rear transmission ratio 46T/23T). | View product >>> |
#808373 | Solid axle pulley 47t Pulley for use with solid rear axle. Impact M2 version only (Impact M2 rear transmission ratio 47T/22T). | View product >>> |
#808376 | Differential pulley 47t Diff. pully for Impact M2 standard diff. 8375. | View product >>> |
#808380 | Engine mounts M2 Machined engine mounts for Impact 2 and M2 all Specs. Fit all NovaMEGA SX-15 engines and all other NR .15 engines. Anodized purple. | View product >>> |
#8114 | Roll-bar Impact M2 Steel roll-over bar, fits all Impact models. | View product >>> |
#901164 | Servo mounting blocks Servo mounting blocks, injection molded composite nylon, used to mount steering and throttle servo. | View product >>> |
#901355 | Brake pads, set of 4 Brake pads, made of special friction material, blue. Must be glued onto steel brake plates 901356. Set of 4. | View product >>> |
#901356 | Steel brake plates VETEQ brake plates made of spring steel. Interchangeable with Vector, Impact and Impulse brake plates. Old style Vector and Impact brake plates (9602) cannot be used on VETEQ. Set of 2. | View product >>> |
#902115 | Mounting-pin tank + rubber cap (2) Complete set for mounting the Serpent 950 fuel tank to the radio plate. | View product >>> |
#902116 | Cap rubber for mounting pin tank (2) A set of two mounting rubbers & o-rings for isolating the fuel tank from vibrations. | View product >>> |
#902138 | Trackrod M3x23 (2) Trackrod M3x23 (2) | View product >>> |
#902250 | Middle bearing block Composite middle bearing block to mount the middle layshaft. For use on the Serpent 950, 705, 835 and all previous models Impact and Impulse and Vector. | View product >>> |
#902252 | Middle shaft steel Middle shaft made from steel for use with the Serpent 950, 835 (4wd) and 705. | View product >>> |
#902410 | 2-speed gearbox LC (no shaft incl) Complete LC gearbox set for use with all Serpent cars. Requires the cars respective LC gearbox shaft to be mounted. | View product >>> |
#902411 | Drive-flange alu with owb Aluminum drive flange for the new LC gearbox. Used to mount the 1st gear, comes complete with one way bearing. Use special formula #1680 One-Way Lub to lubricate the one-way bearing after each hour of use to avoid locking up or slipping. | View product >>> |
#902412 | Adaptor 2-speed LC Steel adaptor for mounting gearbox shoes. Hardened and precision grinded for perfect functioning of the one-way bearing. | View product >>> |
#902413 | Carrier 2nd Gear LC Ultra lightweight aluminium, 2nd speed gear carrier for LC Gearbox. | View product >>> |
#902416 | 2-speed shoe-set LC II A set containing 2 wear resistant material shoes and all the fasteners, springs, grub screws and steel needles required to attach the shoes to the gearbox adaptor. Suitable for use with the LC Gearbox only. | View product >>> |
#902420 | Roller pin steel 5X5 (2) A pair of steel roller pins for use in the LC gearbox. Replaced by 110202 Pin 5x5 (10) | View product >>> |
#902421 | Needle 3x13.8 (4) Set of 4 Roll pins for use with the new LC Gearbox 2 speed adapter. Replaced by 110203 Pin 3x14 (10) | View product >>> |
#902444 | 2-speed gear 44T (2ND) LC Composite 44T 2nd gear for use with new LC Gearbox. | View product >>> |
#902445 | 2-speed gear 45T (2ND) LC Composite 45T 2nd gear for use with new LC Gearbox. | View product >>> |
#902446 | 2-speed gear 46T (2ND) LC Composite 46T 2nd gear for use with new LC Gearbox. | View product >>> |
#902447 | 2-speed gear 47T (1ST) LC 47T composite 1st gear for new LC gearbox. | View product >>> |
#902448 | 2-speed gear 48T (1ST) LC 48T composite 1st gear for new LC gearbox. | View product >>> |
#902449 | 2-speed gear 49T (1ST) LC 49T composite 1st gear for new LC gearbox. | View product >>> |
#902450 | 2-speed gear 50T (1ST) LC 50T composite 1st gear for new LC gearbox. | View product >>> |
#903186 | C + G Clip + washer RCC shocks (12) Set of 4 C-clips (R2), G-clips and nylon washers, suitable for Serpents RCC shocks. | View product >>> |
#903230 | Ball joints 5.8mm frame Set of twenty 5.8mm composite ball joints. | View product >>> |
#903231 | Ball joints set 14+6+2 Set of composite ball joints that includes 14 x 6mm ball joints, 6 x shorter shock end ball joints and 2 x 4mm ball joints. The balljoints feature a text with TOP to indicate right position to press in the ball, for perfect fit. | View product >>> |
#909216 | Adjustable front anti-roll bar blade (male) Adjustable front anti-roll bar blade with ball (male). For Vector all Specs. | View product >>> |
#909217 | Adjustable front anti-roll bar blade (female) Adjustable front anti-roll bar blade, female part. For Vector all Specs. | View product >>> |
#909402 | Pivot point top shockabsorber 4-step (2) Handy set of 2 pivot point tops for your Serpent 4 step shockabsorbers | View product >>> |
#909403 | Ball-joint short lower shock-absorber (4) Handy set of 4 ball-joints for your short lower shock-absorbers. Use 903231 instead. | View product >>> |
#909404 | Spring-support washers (4) Set of four spring support washers. | View product >>> |
#909405 | Shock adjusting nut alu. + O-rings (4) Set of 4 alu. spring-tension adjusting nuts and 4 O-rings to be inserted into the alu. adjusting nuts. O-ring prevents adjusting nut from coming loose. | View product >>> |
#909406 | Shock cap-nut alu. (2) Alu. nut to close up the top pivot point of the 4-step adjustable shock absorber. Set of 2. | View product >>> |
#909407 | O-ring soft-purple (4) Set of 4 O-rings and shims, used to seal and guide the shock rod in the bottom part of the shock cilinder. | View product >>> |
#909440 | Shock-absorber-set key FR+RR Full set (4) of Serpents revolutionary 4-step shock absorbers. Featuring new keyed shock pistons and shafts this set comes with a set of yellow springs. Comes complete with assembly instructions. | View product >>> |
#909441 | Shock-parts frame key FR+RR (2) Complete set (4) of composite parts for Serpents 4-step adjustable shock absorbers. | View product >>> |
#909442 | Piston-rods FR key (2) A set of 2 keyed shock shafts complete with the c-clips required to mount the composite shock pistons. | View product >>> |
#909444 | Piston-rods RR key (2) A set of 2 keyed shock shafts for the rear shocks, complete with the c-clips required to mount the composite shock pistons. | View product >>> |
#909445 | Shock-pistons frame adj+fixed key (2) Complete set of adjustable and non adjustable pistons for use with Serpent shock absorbers. | View product >>> |
#909510 | Centax-II clutch-set (excl. Flywheel) Complete Centax-II clutch set with everything needed to mount it to your engine with the exception of the flywheel. All bearings, shoes, shims and a bell housing with a 16/19 gear ratio is supplied. | View product >>> |
#909512 | Centax-II clutch-housing universal Ultra strong spring steel Centax-II clutch bell housing. | View product >>> |
#909514 | Centax II bearing spacer 5x7 Aluminium spacer for use in the Centax-II clutch system. | View product >>> |
#909515 | Centax II centrifugal shoes (3) A set of 3 carbon flyweights for use in both Centax-I & II clutch systems. | View product >>> |
#909516 | Centax II Spacer Thrustbearing Sapcer for use with Centax-II clutch system. Comes complete with screw. | View product >>> |
#909518 | Centax coilspring 1.8 1.8mm diameter spring steel coil spring for use with the Centax-I and Centax-II clutch systems for use with 3.5cc/.21 engines. A softer version is also available (#6586). Replaced by #909520 | View product >>> |
#909519 | Centax II shims 5 x 10 x 0.3 (2) + 0.5 (1) Set of 3 Centax-II shims in two sizes 0.3 (2) and 0.5 (1). | View product >>> |
#909555 | Centax gear-pinion alu 15t Precision pinion for Centax clutch, made of light-weight 7075-T6 aluminium, hard-anodized to optimize durability. | View product >>> |
#909556 | Centax gear-pinion alu. 16t Precision pinion for Centax clutch, made of light-weight 7075-T6 aluminium, hard-anodized to optimize durability. | View product >>> |
#909558 | Centax gear-pinion alu. 18t Precision pinion for Centax clutch, made of light-weight 7075-T6 aluminium, hard-anodized to optimize durability. | View product >>> |
#909559 | Centax gear-pinion alu. 19t Precision pinion for Centax clutch, made of light-weight 7075-T6 aluminium, hard-anodized to optimize durability. | View product >>> |
#909560 | Centax gear-pinion alu. 20t Precision pinion for Centax clutch, made of light-weight 7075-T6 aluminium, hard-anodized to optimize durability. | View product >>> |
#9611 | Steel brake disks (2) MK-2 Brake discs for all 1/8 and 1/10 scale Serpent cars. Set of 2. | View product >>> |
#9618 | Alu. collar brake-pulley MK-2 Alu. collar for middle pulley on 2-speed axle, used on all Impulse, Impact and Vector versions. | View product >>> |